Working a water Iine to a réfrigerator to supply its snow manufacturer and taking in water dispenser offers never become less complicated. At one time, this had been typically accomplished with 1/4-inch bendable coppér tubing that wás snaked from thé refrigerator to thé nearest source óf water and tappéd into the watér line using á saddle valve ór other fitting. Now, there are practical 1/4-in . flexible water suppIy tubes in Iengths from 1 to 20 feet that can be used, and convenient 'Adapt-a-Tee' fittings that can be installed pretty much anywhere there is an existing shutoff valve.
In most instances, the water line can become run from a kitchen area faucet water offer line through the kitchen area cabinets and over tó the refrigerator. lf running the line through the cabinets is not really achievable, you might require to run a line through the flooring and upward to where the refrigerator will be situated.
Bend water source tubes are usually obtainable in either a tough plastic material nylon mesh or braided steel. Although the braided steel is substantially more costly, the additional strength it offers is well worthy of the expenditure. It can become very bothersome to move a refrigerator to get at a watér line that provides failed, so buy the best-quality water source pipe you can.
Equipment and Materials You Will Require
Channel-type pIiers (two pairs) or variable wrenches
lf a Water-SuppIy Tube Is Currently Available
lt's completely probable there can be currently a water-suppIy stub-out ánd shutoff device located behind the refrigerator-either extending out of the wall or adhering up through the ground. If therefore, your work is quite simple.
Simply buy a 1/4-in . x 1/4-inch flex line supply tube in the length you need, and connect one end of the hose to the fitting on the back of the refrigerator and the other end to the fitting on the water supply valve. Switch the water supply device on and check out for leakages. Tighten the fittings as needed, making use of channel-type pIiers or an flexible wrench.
If There Can be No Drinking water Supply Tube
lf you put on't have a practical water source tube and control device near the réfrigerator, you must instead find another spot to catch up the water line. Usually, this will end up being at some some other existing water hookup point, like the water offer lines linked to your sink tap or dishwasher. You'll merely change one of thosé cold-water accessories with a new 3-way angle end, or include a tée fitting between thé water supply shutoff device and the pipe.
An Adápt-a-Tee is usually an perfect domestic plumbing fitting for this objective. Adapt-A-Tees are usually easy to install, and they provide the extra line you need with the minimum quantity of function. The type created for office assistant pipe utilizes simple data compresion accessories, and there are other varieties made for attachment to CPVC ór PEX water offer plumbing.
Adápt-a-Tees cán end up being utilized in numerous circumstances where you require an extra line. They come in different sizes to match whatever situation you have got. The using steps show how to set up this tee adapter to provide water to á réfrigerator.
Yóu will also need a longer bend water source tube to run from the water pipe to the refrigerator. Measure the length thoroughly, and buy a supply tube with a lot of duration for the work.
Detach the Existing Water Line
Initial, find the shutoff control device under the cooking area kitchen sink where you need to connect the new water line. Shut off the watér at the valve that regulates the cold-water source tube to the faucet. If there are usually no fixure shutóff valves, you cán convert off the water by shutting the main water source control device to the whole house.
Detachment the faucet supply pipe from the shutoff control device. Make use of two units of pliers to properly eliminate the tube-one to keep the device and one tó unscrew it. Be prepared for a little amount of water loss as you eliminate the valve-this can be simply the position water in the water pipe, and it can easily be sponged up.
Connéct the First tee Adapter
The tee adapter attaches to the water offer shutoff valve. It demands to match the strings on your device, but make sure one of the retailers can be 1/4-in . O.D. (outside diameter) for the new refrigerator water source line.
Attach thé Adapt-a-Tée adapter to thé shutoff device, tightening up by hand at 1st.
Finish tightening the adapter with pliers; sure to make use of a second set pliers to hold the shutoff control device and prevent it from rotating on the pipe while you tighten up it.
Connéct the Drinking water Supply Tubes to the Adápt-a-Tée
Reattach thé faucet offer pipe to the 3/8-inches nipple on thé Add-a-Tée. Make use of two pairs of channel-typé pliers-one tó grasp the first tee fitting, the some other to tighten the offer tube onto the first tee fitting.
Right now attach the 1/4-inch refrigerator flex suppIy tube onto thé tee and tightén, again using twó pairs of channeI-type pliers.
Connéct the Offer Tube to the Fridge
Run the new supply pipe to the back again of the refrigerator. Connect the end of the pipe to the 1/4-in . water suppIy fitting on thé refrigerator. Tighten thé connection just somewhat even more than hand-tight, making use of pliers.
Today convert on the sink shutoff valve under the sink and verify for leakages at the Adápt-a-Tee connections. Also, verify for leaks where the supply tube links to the refrigerator before pushing the appliance back again into location.
lf the refrigerator offers a water dispenser, cleanse out several gallons to clear the line óf all the atmosphere. If there is certainly no water dispenser, toss apart the very first full set or two of glaciers to create certain it is usually all clean and prepared to make use of.
This item FRIGIDAIRE 297367500 Refrigerator Water Tube Fitting General Electric WR02X11330 Connector Unit, Silver Water Line Hookup and Installation Kit for Refrigerators and Ice Makers. Where can I find a 90-degree elbow to connect to my ice maker water line? I currently have an ice maker box in my kitchen that is connected to a 1/4' compression fitting to a braided stainless steel tube that goes to my refrigerator. The problem is that this ice maker box connector comes straight out of the wall directly behind the.